Automatic screw driving & non-standard automation equipment — Manufacturer since 2011
CB CBZINChengbo Intelligent Technology
Home/Guides/Screw feeding problems
Technical guide

Common screw feeding problems, and what actually causes them

Almost every feeding fault traces back to one of six things, and the screw itself is responsible for more of them than the machine is.

At a glanceMeasure the screws first Head diameter, head height and shank straightness vary by batch. Twenty screws against a known-good batch answers most mis-pick complaints. · Match the feed method to the head Vacuum pick-up for small heads and low volume; blow feed once a single screw type runs in volume. Neither is universal.

Most engineers arriving here go straight to one of these:

Technical guide

The first suspect is the screw, not the feeder. Head diameter and head height vary between batches and between suppliers, and a vacuum cup sized for the nominal head will mis-pick the moment a batch arrives with a slightly larger head or a burr on the rim. Shank straightness matters for the same reason: a screw that is a few hundredths out of straight will feed down a tube and then arrive at the bit at an angle. Before changing any setting on the machine, measure twenty screws from the batch in use against twenty from a batch that ran well.

The second is the feed method being asked to do something it is not suited to. Vacuum pick-up is reliable for small heads at low volume and becomes marginal as head size and volume rise, because the cup has to both hold and release positively. Blow feed is the opposite: it needs a screw that presents cleanly and a tube that is short and gentle enough that the screw does not tumble. A long tube with a tight bend is a jam waiting for a humid day, and humidity is the third cause — damp air makes screws stick to each other and to the tube wall. Our platforms specify clean dry air at 0.4–0.6 MPa for exactly this reason; wet or oily air is the most common cause of feeding faults on this type of machine.

The remaining three are mechanical and get progressively more expensive to ignore. Static builds on plastic-headed screws and on dry tube walls, so a screw clings instead of dropping. The escapement wears: the part that separates one screw from the queue is a consumable in disguise, and a worn escapement double-feeds long before it stops feeding at all. And the bowl, if there is one, bridges when the queue is too full — which is why 'fill it to the top' is worse advice than 'keep it between half and two thirds'. None of these are fixed by turning up the air pressure, and several get worse.

Last updated 2026-11-20. Screw range, torque and cycle-time figures reflect the current published platform specifications.

What to specify

Key points to take away

The practical conclusions from the sections above.

Measure the screws first

Head diameter, head height and shank straightness vary by batch. Twenty screws against a known-good batch answers most mis-pick complaints.

Match the feed method to the head

Vacuum pick-up for small heads and low volume; blow feed once a single screw type runs in volume. Neither is universal.

Keep the blow tube short and gentle

A long tube with a tight bend makes screws tumble. Every bend is a place a screw can stop.

Dry air is not optional

0.4–0.6 MPa of clean dry air. Wet or oily air is the usual cause of feeding faults on this class of platform.

Static, on plastic heads

Dry tube walls plus plastic-headed screws make screws cling instead of dropping. It looks like a jam and is not one.

The escapement is a consumable

A worn escapement double-feeds long before it stops feeding. If double-feeds appear gradually, suspect it before the bowl.

Common questions

Frequently asked questions

The machine worked for months and now double-feeds. What changed?
Usually the escapement, and sometimes the screw batch. Gradual onset points at wear; sudden onset points at a new box of screws. Checking both takes ten minutes and saves swapping parts that were fine.
Can I run two different screw types on one machine?
Yes if the feed path is changed between them, not if they share a bowl at the same time. Mixed screw types in one queue is the fastest way to make a reliable feeder unreliable.
Does higher air pressure fix feeding faults?
Rarely, and it often makes them worse — more pressure means more tumbling, more static and more double-feeds. Fix the tube, the air quality or the screw batch instead.
Keep reading

Related pages

Not sure which applies to you?

Describe the part and the joint and we will tell you which configuration fits — or whether you do not need a machine at all.