Automatic screw driving & non-standard automation equipment — Manufacturer since 2011
CB CBZINChengbo Intelligent Technology
Home/Video demos
Video demos

Watch the machines running

Short clips filmed on our own production floor in Dongguan — robotic cells, bench-top units and three-axis platforms driving screws into real fixtures. Filmed upright on the line, exactly as they run.

Robotic screw driving cellSix-axis arm carrying a screw driving end-effector, indexing over a pallet fixture.Watch on YouTube
Bench-top automatic screw driving machineBench-top unit with an automatic screw feeder and touch-screen HMI, set up for a small part.Watch on YouTube
Three-axis screw driving platformX-axis gantry indexing a large fixture plate for multi-point fastening.Watch on YouTube
In-line gantry screw driving headOverhead screw driving head fastening a moulded part held in a product fixture.

Want to see a machine running on your part? Send us a drawing or a screw specification and we can film a test run for you.

What to look at

Four clips, four different ways to hold a part

Forty seconds of video is easy to watch and easy to misread. The useful part of each clip is not the arm moving — it is how the part is held and how the screw arrives, because that is what decides whether the machine works on your product or only on the one in the video. Below is what to look at in each, written against the clip running above.

Robotic screw driving cell · six-axis arm

Look at the end effector, not the arm. The driver is on a floating mount so the bit finds the screw head instead of stabbing at it. Below it sits a black pallet with orange tape marks and two blue proximity sensors — that is the fixture locating the part, and the sensors are what stop the cycle if a part is loaded crooked.

Bench-top automatic screw driving machine · vibration bowl + HMI

The red bowl on the right is the screw feeder: it orients screws and hands them to the driver one at a time, which is why the operator never picks a screw up. The touch screen below shows the point list and the tighten result per screw. This is the format most buyers start with, because it drops onto an existing bench.

Three-axis screw driving platform · X-Y gantry

Watch the fixture plate travel, not the head. A large black plate carries the part through multiple fastening points in one clamping; the pneumatic cylinder at the edge holds it down so the part cannot lift as the bit withdraws. Fewer clamps per part is where the labour saving actually comes from.

In-line gantry screw driving head · overhead head

This head comes down from above onto a moulded part sitting in a shaped fixture. Note the fixture is cut to the part outline rather than being a flat plate — that is what keeps a thin-walled moulding from flexing while the screw pulls it down, and it is the difference between a consistent torque reading and a random one.

If your part is not represented here, that is normal rather than a gap: the platforms are standard, the tooling is not. A gripper, a shaped nest or a vacuum plate is designed per part, and that tooling is usually the larger half of the engineering work. The platform range lists what each machine can carry, and the machine selector narrows it down to one or two models from the part size and the screw count.

How to judge a demo

Five things that separate a real demo from a rendered one

Anyone selling automation can produce a smooth animation of a machine driving screws into a perfect part. It costs nothing and proves nothing. When you are comparing videos from several suppliers, these five checks do the separating:

  • The screw transfer is on camera. A real screw feeder is visible: a vibration bowl, a step feeder or an air line handing a single screw to the bit. In a render, screws appear under the driver from nowhere, and nobody notices.
  • The part is a real part. Moulding flash, a taped-on sensor, a used fixture plate with witness marks — those are the signs of a machine earning its keep. A perfectly uniform grey block is a sign of a CAD render.
  • The HMI shows per-point results. Real machines report screw by screw. A single green lamp can be animated in an afternoon; a point list updating with a torque value per screw has to come from a controller actually running.
  • The camera does not cut at the critical moment. Watch whether the clip stays on the driver through the whole fastening, or cuts exactly as the bit meets the head. Cutting there is how a failed drive is hidden.
  • The background is a factory. Cables in trunking, chip on the floor, someone else’s machine behind — that is a workshop. A seamless gradient behind the machine is a studio, and a studio is where renders are made.

All four clips above pass all five, by construction rather than by claim: they were filmed on a phone on our floor, which is also why the framing is imperfect. You can see the same plant in more detail in the 360° factory tour, where the workshops behind these machines are walkable, and the assembly benches are in the frame at the same time as the machines.

Screw driving platforms in these clips

Shared specifications across the machines shown above.

ParameterValue
Screw size rangeM1.7 – M5.0
Locking range (X × Y × Z)500 × 400 × 100 mm
Repeat positioning accuracy±0.02 mm
Standard cycle time (arm)0.37 – 0.41 s / screw
Payload4 kg — 5 kg downward positioning
Moving speed0.1 – 800 mm/s per axis
DriveStepper / servo motors (Japan)
TransmissionTiming belt and/or precision linear guide
Power supplyAC 220 V, 50 Hz, single phase, 1.5 kW
Working air pressure0.4 – 0.6 MPa
Protection ratingIP40
Control optionsEPSON controller / PLC / PC control / teach pendant
Common questions

Questions these videos usually raise

Asked by buyers after watching the clips, answered the same way we answer them by email.

Can you film a test run on our part before we order?
Yes. Send a drawing or a sample plus the screw specification, and we run it on the closest platform we have and film the result. You get the clip before any purchase order, so you can check the fastening, the cycle and the fixturing on your own part rather than on ours.
Are these clips real machines or rendered animations?
Real machines on our production floor in Dongguan, filmed on a phone held upright, which is why they are portrait. There is no rendering, no stock footage and no speed-up; each clip runs at normal speed so the cycle time you see is the cycle time the machine does.
Why are the videos portrait instead of widescreen?
They were shot for phone feeds, where most of our buyers first see them. The same clips are published on YouTube Shorts, and each card above links to its YouTube version if you prefer that player. If you need a widescreen copy for an internal review or a tender document, ask and we export one.
Which machine in these clips suits a small part with four to six screws?
The bench-top unit. It carries its own screw feeder and a touch screen, needs a standard bench and single-phase power, and is the lowest-cost way to stop hand driving screws. Move to a three-axis platform only when the part outgrows the bench-top working envelope or you need multiple points in one clamping.
What cycle time should I expect from what I see?
The arm platforms are specified at 0.37 to 0.41 seconds per screw, but the cycle a buyer actually gets also includes loading, clamping and transfer. Use the cycle time calculator with your screw count and load time instead of reading a number off a video — the calculator shows both the ideal and the realistic figure.
Can the machine detect a screw that did not go in?
Yes, and it is visible in the clips as a per-point result on the HMI rather than a single pass or fail lamp. Missing-screw detection and automatic re-tightening are standard on the arm platforms. Ask for the detection method in writing if your customer requires it, because torque monitoring and depth monitoring catch different failure modes.

Send us your part and screw specification

Tell us the product, the screw and the required cycle time. We reply with a suggested configuration and a quotation.