Automatic screw driving & non-standard automation equipment — Manufacturer since 2011
CB CBZINChengbo Intelligent Technology
Home/Guides/Choosing tightening torque
Technical guide

How to choose and set tightening torque

Torque is not a number you pick from a table. It is a window you find, and then a tightening strategy you choose to land inside it repeatably.

At a glanceFind the window, not the number Increase torque on real parts and record where the joint stops closing and where it fails. The gap between the two is your window. · Window width decides strategy Wide window: single-stage torque stop. Narrow window: two-stage tightening with the final stage monitored.

Most engineers arriving here go straight to one of these:

Technical guide

Start by finding the window rather than the target. Tighten a sample of real parts with real screws, increasing torque in small steps, and record two things: the torque at which the joint stops closing, and the torque at which something fails — thread strip, boss crack, insert pull-out. The window sits between them, and its width is what decides everything that follows. A joint that closes gradually over a wide torque range is forgiving. A joint that bottoms out within a few degrees of rotation is not, and no amount of tightening the tolerance on the driver will fix that.

Then choose the strategy the window allows. A wide window on a robust joint tolerates a single-stage torque stop, which is the simplest and fastest thing a machine can do. A narrow window needs two-stage tightening: run down fast to a seating torque, then make the final turn slowly with the result monitored, and reject the part if the angle or the torque falls outside the limits. This is also the strategy that catches a cross-threaded screw — the torque climbs while the angle barely moves, and a single-stage machine will happily report success.

Finally decide what you are going to prove. If nothing is recorded, torque is a setting somebody changed once. If every screw's torque and angle is written to a record, torque becomes a process you can audit, and a re-drive can be triggered automatically when a screw is missing or floating. That decision belongs before the machine is configured, because on our platforms it is a setting and an interface, not a rebuild. Our screws run M1.7 to M5.0, tightening records can carry torque, angle and pass/fail per screw, and the driver's minimum settable torque must sit below your target — that last check kills more projects than any other, and it is free to do before you buy.

Last updated 2026-11-20. Screw range, torque and cycle-time figures reflect the current published platform specifications.

What to specify

Key points to take away

The practical conclusions from the sections above.

Find the window, not the number

Increase torque on real parts and record where the joint stops closing and where it fails. The gap between the two is your window.

Window width decides strategy

Wide window: single-stage torque stop. Narrow window: two-stage tightening with the final stage monitored.

Two-stage catches cross-threading

Torque rising while angle stays flat is a cross-thread. A single-stage machine reports it as a success.

Check the driver's minimum setting

If the driver cannot be set below your target torque, the machine cannot hit it repeatably. Verifying this costs nothing and saves the project.

Decide the record before the build

Torque, angle and result per screw, or nothing at all. On our platforms this is a configuration and an interface, not a retrofit.

Re-drive on failure

With a record in place, a missing or floating screw can trigger an automatic re-drive instead of a rework station downstream.

Common questions

Frequently asked questions

Is there a standard torque for M3 screws?
There are published values for standard threads in standard materials, and they are a starting point, not an answer. The joint decides: a brass insert in plastic and a steel nut on steel strip take very different torque at the same thread size.
How do I know the torque is right without destroying parts?
Tighten to failure deliberately on a small sample, and keep the parts. Knowing where the joint fails is the only way to know how much margin the window has — and the failed parts tell you which failure mode you are closest to.
Can the machine reject a bad screw automatically?
Yes, when torque and angle are monitored per screw. A screw that stops short, cross-threads, or floats is detected from the torque-angle curve rather than from the operator noticing it later.
Keep reading

Related pages

Not sure which applies to you?

Describe the part and the joint and we will tell you which configuration fits — or whether you do not need a machine at all.